Noise-based ballistic wave passive seismic monitoring. Part 1: body waves

Unveiling the mechanisms of earthquake and volcanic eruption preparation requires improving our ability to monitor the rock mass response to transient stress perturbations at depth. The standard passive monitoring seismic interferometry technique based on coda waves is robust but recovering accurate and properly localized P- and S-wave velocity temporal anomalies at depth is intrinsically limited by the complexity of scattered, diffracted waves. In order to mitigate this limitation, we propose a complementary, novel, passive seismic monitoring approach based on detecting weak temporal changes of velocities of ballistic waves recovered from seismic noise correlations. This new technique requires dense arrays of seismic sensors in order to circumvent the bias linked to the intrinsic high sensitivity of ballistic waves recovered from noise correlations to changes in the noise source properties. In this work we use a dense network of 417 seismometers in the Groningen area of the Netherlands, one of Europe's largest gas fields. Over the course of 1 month our results show a 1.5 per cent apparent velocity increase of the P wave refracted at the basement of the 700-m-thick sedimentary cover. We interpret this unexpected high value of velocity increase for the refracted wave as being induced by a loading effect associated with rainfall activity and possibly canal drainage at surface. We also observe a 0.25 per cent velocity decrease for the direct P-wave travelling in the near-surface sediments and conclude that it might be partially biased by changes in time in the noise source properties even though it appears to be consistent with complementary results based on ballistic surface waves presented in a companion paper and interpreted as a pore pressure diffusion effect following a strong rainfall episode. The perspective of applying this new technique to detect continuous localized variations of seismic velocity perturbations at a few kilometres depth paves the way for improved in situ earthquake, volcano and producing reservoir monitoring.

Noise-based ballistic wave passive seismic monitoring – Part 2: surface waves

We develop a new method to monitor and locate seismic velocity changes in the subsurface using seismic noise interferometry. Contrary to most ambient noise monitoring techniques, we use the ballistic Rayleigh waves computed from 30 d records on a dense nodal array located above the Groningen gas field (the Netherlands), instead of their coda waves. We infer the daily relative phase velocity dispersion changes as a function of frequency and propagation distance with a cross-wavelet transform processing. Assuming a 1-D velocity change within the medium, the induced ballistic Rayleigh wave phase shift exhibits a linear trend as a function of the propagation distance. Measuring this trend for the fundamental mode and the first overtone of the Rayleigh waves for frequencies between 0.5 and 1.1 Hz enables us to invert for shear wave daily velocity changes in the first 1.5 km of the subsurface. The observed deep velocity changes (±1.5 per cent) are difficult to interpret given the environmental factors information available. Most of the observed shallow changes seem associated with effective pressure variations. We observe a reduction of shear wave velocity (–0.2 per cent) at the time of a large rain event accompanied by a strong decrease in atmospheric pressure loading, followed by a migration at depth of the velocity decrease. Combined with P-wave velocity changes observations from a companion paper, we interpret the changes as caused by the diffusion of effective pressure variations at depth. As a new method, noise-based ballistic wave passive monitoring could be used on several dynamic (hydro-)geological targets and in particular, it could be used to estimate hydrological parameters such as the hydraulic conductivity and diffusivity.

Virtual Sources of Body Waves from Noise Correlations in a Mineral Exploration Context.

The extraction of body waves from passive seismic recordings has great potential for monitoring and imaging applications. The low environmental impact, low cost, and high accessibility of passive techniques makes them especially attractive as replacement or complementary techniques to active‐source exploration. There still, however, remain many challenges with body‐wave extraction, mainly the strong dependence on local seismic sources necessary to create high‐frequency body‐wave energy. Here, we present the Marathon dataset collected in September 2018, which consists of 30 days of continuous recordings from a dense surface array of 1020 single vertical‐component geophones deployed over a mineral exploration block. First, we use a cross‐correlation beamforming technique to evaluate the wavefield each minute and discover that the local highway and railroad traffic are the primary sources of high‐frequency body‐wave energy. Next, we demonstrate how selective stacking of cross‐correlation functions during periods where vehicles and trains are passing near the array reveals strong body‐wave arrivals. Based on source station geometry and the estimated geologic structure, we interpret these arrivals as virtual refractions due to their high velocity and linear moveout. Finally, we demonstrate how the apparent velocity of these arrivals along the array contains information about the local geologic structure, mainly the major dipping layer. Although vehicle sources illuminating array in a narrow azimuth may not seem ideal for passive reflection imaging, we expect this case will be commonly encountered and should serve as a good dataset for the development of new techniques in this domain.

PACIFIC develops mineral exploration techniques that have a relatively low impact on the environment. This document is an assessment of this impact, but also of the environmental footprint of all activities related to the project. PACIFIC environmental footprint is still significant because of plane travels linked to transnational meetings. Learn more about it by reading the following document.

https://www.pacific-h2020.eu/wp-content/uploads/pacific_documents-on-impact_the-environmental-impact-of-pacific-report-1.pdf 

Technique now possible due to improvements in lithium batteries which power monitoring equipment

Article in the Canadian press by Jeff Walters · CBC News · Posted: Jun 12, 2019 1:28 PM ET  https://www.cbc.ca/news/canada/thunder-bay/thunder-bay-pacific-new-exploration-1.5172168 

Download PACIFIC poster presented at the American Geophysical Union (AGU) in Washington DC (10-14 December 2018)

https://www.pacific-h2020.eu/wp-content/uploads/PACIFIC-poster.pdf 

All you want to know about the PACIFIC project (Passive seismic techniques for environmentally friendly and cost efficient mineral exploration) is there !

PACIFIC - H2020 research project in mineral exploration (pacific-h2020.eu)

Sometimes noise is incredibly helpful.

By Rahul Rao, Popular Science (January 28, 2021)

For the full article, please visit How trains can help scientists study what's underground | Popular Science (popsci.com)

Check out our project log on Research Gate: https://www.researchgate.net/project/PACIFIC-H2020